Congratulations, you’ve got accomplished your quilt high and are prepared to complete it off with a lovely binding! Binding not solely provides an ornamental contact to your quilt, nevertheless it additionally protects the uncooked edges of the material. Whereas it could appear to be a frightening activity at first, ending a quilt binding is definitely fairly easy and could be accomplished in only a few hours. On this information, we’ll stroll you thru your complete technique of ending a quilt binding, from getting ready the binding strips to securing the ultimate stitches. Whether or not you are a newbie quilter or a seasoned professional, we’ll present clear and concise directions that can assist you create a lovely and safe end to your quilt.
Earlier than you start, collect your supplies. You will have:
– Quilt binding strips
– Coordinating thread
– Stitching machine
– Iron and ironing board
– Scissors
– Measuring tape or ruler
– Elective: Binding clips or pins
Upon getting your supplies, you are prepared to begin getting ready the binding strips. First, measure the perimeter of your quilt high. Minimize the binding strips to the specified width, sometimes 2 1/2 inches huge. Be part of the binding strips collectively utilizing a diagonal seam. Press the seam allowances open. Fold the binding strip in half lengthwise, flawed sides collectively, and press. This can create a folded binding strip that is able to be sewn to the quilt high. Now that your binding strips are ready, you are prepared to connect them to the quilt high.
Blind-Sew the Binding
Blind-stitching is the strategy of stitching the quilt binding by hand and hiding the stitches on the fitting aspect of the quilt. This creates a clear, professional-looking end.
Supplies you will want:
- Quilt binding
- Needle
- Thread
- Scissors
Step-by-step directions:
1. Fold the binding over the uncooked fringe of the quilt
Begin on the middle of 1 aspect of the quilt and fold the binding over the uncooked edge by about 1/4 inch. Safe it with a couple of hand stitches.
2. Make a small sew into the folded fringe of the binding
Utilizing a small sew, insert the needle into the folded fringe of the binding, simply above the uncooked fringe of the quilt. Pull the thread by means of.
3. Make a small sew into the quilt high
Insert the needle into the quilt high, about 1/4 inch away from the primary sew. Pull the thread by means of.
4. Repeat steps 2 and three alongside your complete edge
Proceed making small stitches into the binding and quilt high, alternating sides. Maintain the stitches shut collectively and even.
5. Trim any extra binding
When you attain the top of the aspect, trim any extra binding. Go away about 1/4 inch of overhang.
6. Fold the binding over the top of the quilt
Fold the binding over the top of the quilt by 1/4 inch. Safe it with a couple of hand stitches.
7. Proceed blind-stitching across the complete quilt
Repeat steps 1-6 across the complete perimeter of the quilt. If you attain the place to begin, make sure that the binding is securely folded and stitched.
8. Trim any extra thread
Upon getting completed blind-stitching, trim any extra thread.
9. Knot the thread and safe it
Tie a small knot in the long run of the thread and pull it tight to safe it. Trim any extra thread.
10. Press the binding
Use a heat iron and a press fabric to press the binding flat. This can assist to set the stitches and provides the quilt a completed look.
Suggestions for blind-stitching the binding:
- Use a small needle and skinny thread. This can assist to make the stitches much less seen.
- Maintain the stitches shut collectively and even. This can assist to create a professional-looking end.
- Take your time and be affected person. Blind-stitching is a gradual course of, however it’s well worth the effort.
Troubleshooting blind-stitching issues:
| Downside | Resolution |
|---|---|
| Stitches are seen on the fitting aspect of the quilt | Use a smaller needle and thinner thread. Maintain the stitches nearer collectively. |
| Binding shouldn’t be securely hooked up | Ensure to make the stitches shut collectively and pull the thread tight. |
| Binding is puckered | Gently stretch the binding as you sew it. |
Add a Binding to a Rag Quilt
A rag quilt is a kind of quilt made out of strips of material sewn collectively. The sides of the quilt are then certain with a strip of material to complete the quilt. Binding a rag quilt is a comparatively easy course of that may be accomplished in a couple of hours.
To bind a rag quilt, you will want the next supplies:
- A rag quilt
- A strip of material for the binding
- A stitching machine
- Thread
- A needle
- Scissors
Upon getting gathered your supplies, you’ll be able to start binding the quilt. Comply with these steps to bind a rag quilt:
- Minimize the binding strips. The binding strips must be lower to the width of the completed binding, plus 1/2 inch for seam allowances. The size of the binding strips will rely upon the dimensions of the quilt.
- Sew the binding strips collectively. Sew the binding strips collectively finish to finish to create one lengthy strip of material.
- Connect the binding to the quilt. Pin the binding strip to the sting of the quilt, proper sides collectively. Sew the binding to the quilt utilizing a 1/4-inch seam allowance.
- Fold the binding over the sting of the quilt. Fold the binding over the sting of the quilt in order that the uncooked fringe of the quilt is roofed. Pin the binding in place.
- Sew the binding to the quilt. Sew the binding to the quilt utilizing a 1/4-inch seam allowance.
- End the binding. Trim the surplus binding from the corners of the quilt. Fold the binding below at first and finish of the quilt and stitch it down.
Troubleshooting Binding Points
- The binding is simply too free. If the binding is simply too free, it won’t keep in place. To repair this, you’ll be able to sew the binding down extra securely or use a wider binding strip.
- The binding is simply too tight. If the binding is simply too tight, it’ll puckered or trigger the quilt to ripple. To repair this, you’ll be able to loosen the strain in your stitching machine or use a narrower binding strip.
- The binding is uneven. If the binding is uneven, it’ll look sloppy. To repair this, you should use a ruler to measure the width of the binding as you sew it on.
- The binding is coming undone. If the binding is coming undone, it signifies that it was not sewn on securely. To repair this, you’ll be able to resew the binding utilizing a stronger thread or a wider sew.
| Binding Challenge | Resolution |
|---|---|
| The binding is simply too free. | Sew the binding down extra securely or use a wider binding strip. |
| The binding is simply too tight. | Loosen the strain in your stitching machine or use a narrower binding strip. |
| The binding is uneven. | Use a ruler to measure the width of the binding as you sew it on. |
| The binding is coming undone. | Resew the binding utilizing a stronger thread or a wider sew. |
Restore a Torn Quilt Binding
A torn quilt binding could be a irritating downside, nevertheless it’s one that may be simply fastened with a couple of easy steps. Here is how one can do it:
1. Collect Your Provides
You will have the next provides:
- A needle and thread
- A thimble
- A pair of scissors
- A bit of material that matches the quilt binding
2. Minimize a Patch
Minimize a chunk of material that’s barely bigger than the tear within the quilt binding. The patch must be not less than 1/2 inch wider and 1/2 inch longer than the tear.
3. Fold the Patch in Half
Fold the patch in half, flawed sides collectively. Press the fold with an iron.
4. Pin the Patch in Place
Pin the patch over the tear within the quilt binding, centering the patch over the tear. Ensure that the uncooked edges of the patch are aligned with the uncooked edges of the quilt binding.
5. Sew the Patch in Place
Sew the patch in place utilizing a blind sew. To do a blind sew, insert the needle into the material on the high of the binding, just under the fold. Carry the needle out by means of the material on the backside of the binding, simply above the fold. Repeat this course of, taking small stitches, till the patch is sewn in place.
6. Trim the Extra Cloth
As soon as the patch is sewn in place, trim the surplus material across the edges of the patch. Watch out to not lower too near the stitching.
7. Press the Binding
Press the binding to set the stitches and provides the quilt a completed look.
Options to Repairing a Torn Quilt Binding
If you do not have the time or endurance to restore a torn quilt binding, there are a couple of options you can attempt:
1. Use a Quilt Binding Tape
Quilt binding tape is a self-adhesive tape that can be utilized to cowl up torn or broken quilt bindings. It’s obtainable in a wide range of colours and widths, so you’ll find a tape that matches your quilt.
2. Use a Cloth Glue
Cloth glue can be utilized to attach down torn or indifferent quilt bindings. Make sure to use a material glue that’s particularly designed for quilts, as some glues can injury the material.
3. Use a Stitching Machine
If in case you have a stitching machine, you should use it to stitch the torn quilt binding again in place. It is a extra everlasting resolution than utilizing quilt binding tape or material glue, however it’s also extra time-consuming.
Stopping Torn Quilt Bindings
One of the simplest ways to stop torn quilt bindings is to handle your quilt. Listed here are a couple of ideas:
- Retailer your quilt in a cool, dry place.
- Keep away from exposing your quilt to direct daylight.
- Wash your quilt on a mild cycle in chilly water.
- Dry your quilt on a low warmth setting.
- Iron your quilt on a low warmth setting.
By following the following tips, you’ll be able to assist to maintain your quilt trying its finest for years to come back.
Minimize the Binding Strips
As soon as you’ve got chosen your material and calculated the size of binding you want, it is time to lower the binding strips. For the standard 1/2-inch double-fold binding, you will want to chop strips which can be 2 1/4 inches huge. To do that:
- Minimize two strips of material which can be twice the width of the completed binding plus 1 inch. For a 1/2-inch binding, this may be 2 1/2 inches huge.
- Sew the 2 strips collectively, proper sides collectively, alongside one lengthy edge. Press the seam open.
- Fold the strip in half lengthwise, flawed sides collectively, and press.
You now have a steady strip of binding that’s 1/4 inch narrower than the completed width of your quilt. The additional 1/4 inch can be used to create the mitered corners.
Mark the Quilt Edges for Binding
Measure and Trim the Quilt
Lay the quilt flat on a big floor. Measure the quilt high, backside, and sides to make sure it’s sq.. If wanted, trim any extra material alongside the perimeters to create a straight and even quilt.
**Tip:** To make sure accuracy, use a quilting ruler or measuring tape particularly designed for quilting.
Fold the Binding in Half
Fold the quilt binding in half lengthwise, bringing the uncooked edges collectively. Press the fold to create a crease.
**Tip:** For a mitered nook, fold the binding at a 45-degree angle. This can permit for a seamless and professional-looking end.
Mark the Binding Edges
Fold the quilt again on itself, beginning at one nook. Align the folded fringe of the binding with the uncooked fringe of the quilt. Press the binding in opposition to the quilt to create a crease.
Repeat this course of alongside all sides of the quilt, creating creases each 2-3 inches.
Unfold the Quilt and Pin the Binding
Unfold the quilt and open the binding. Align the creases on the binding with the uncooked edges of the quilt. Pin the binding to the quilt, beginning within the middle of every aspect and dealing outwards.
**Tip:** Use quilting pins which can be lengthy sufficient to penetrate each the binding and the quilt layers.
When pinning the corners, fold the binding at a 45-degree angle and align the uncooked edges. This can assist create a mitered nook.
**Notice:** For a safe and sturdy bind, the binding ought to overlap the quilt edges by roughly 1/4 inch on all sides.
Sew the Binding to the Quilt
Utilizing a stitching machine, sew the binding to the quilt. Select a sew size that’s applicable for the load of the material. Sew across the complete quilt, beginning and stopping within the middle of 1 aspect.
**Tip:** For an ornamental end, think about using an ornamental sew or topstitching the binding to the quilt.
Trim the Corners
As soon as the binding is sewn, trim the surplus material from the corners. This can assist create a neat {and professional} end.
**Tip:** Use sharp scissors to keep away from fraying the material.
Fold the Binding Over and Pin
Fold the binding over the uncooked edges of the quilt, aligning the folded edge with the sewn edge. Pin the binding across the complete quilt, once more beginning within the middle of every aspect and dealing outwards.
**Tip:** When folding the corners, miter the binding as earlier than for a seamless end.
Sew the Binding to the Again of the Quilt
Utilizing a blindstitch, sew the binding to the again of the quilt. This sew will conceal the stitching line, making a clear and completed look.
**Tip:** For a extra sturdy bind, contemplate hand-stitching the binding for further safety.
Bind a Quilt with a Curved Edge
Binding a quilt with a curved edge requires a bit extra precision and a focus to element than binding a quilt with a straight edge. Nonetheless, with a bit of endurance and care, you’ll be able to obtain a lovely and professional-looking end.
Listed here are the steps on how one can bind a quilt with a curved edge:
1. Put together the quilt and binding
Trim the quilt to the specified dimension and form. Minimize the binding strips to the specified width and size. The width of the binding strips will rely upon the thickness of the quilt and the specified completed look.
2. Sew the binding strips collectively
Be part of the binding strips along with a diagonal seam. Make sure to trim the surplus material from the seam allowance.
3. Connect the binding to the quilt
Align the uncooked fringe of the binding with the uncooked fringe of the quilt. Pin the binding in place, beginning on the middle of 1 aspect and dealing your manner across the quilt. Use small, even stitches to stitch the binding to the quilt.
4. Miter the corners
If you attain a nook, you will want to miter the binding to create a neat and tidy end. To miter a nook, comply with these steps:
a) Mark a diagonal line from the nook of the quilt to the outer fringe of the binding.
b) Fold the binding alongside the diagonal line, bringing the 2 uncooked edges collectively.
c) Trim the surplus material from the seam allowance.
d) Unfold the binding and press the seam allowance.
e) Align the mitered nook with the nook of the quilt and stitch in place.
5. End the binding
Upon getting hooked up the binding to the quilt, you’ll be able to end it by both hand-stitching or machine-stitching the binding down. In case you are hand-stitching the binding, use small, even stitches to stitch the binding to the quilt.
In case you are machine-stitching the binding, use a blind hem sew to stitch the binding down. This sew will create a hidden sew that won’t be seen from the fitting aspect of the quilt.
6. Trim the surplus binding
As soon as the binding is completed, trim any extra binding from the perimeters of the quilt.
7. Press the quilt
Press the quilt to set the binding and provides it a professional-looking end.
| Curved Edge Binding Strategies | Description |
|---|---|
| Bias binding | Bias binding is lower on the diagonal of the material, which supplies it a slight stretch. This makes it preferrred for binding curved edges as a result of it may well simply conform to the form of the quilt. |
| Double-fold binding | Double-fold binding is made by folding the material over twice, making a slim strip of material with two completed edges. One of these binding is extra sturdy than bias binding, however it’s also tougher to stitch on. |
| Hong Kong binding | Hong Kong binding is a kind of bias binding that’s made with a slim strip of material that’s folded over and sewn to the quilt. One of these binding could be very sturdy and sturdy, and it’s also comparatively simple to stitch on. |
How To End A Quilt Binding
Ending a quilt binding is a important step within the quilt-making course of, because it provides the quilt a cultured {and professional} look. There are various other ways to complete a quilt binding, and the very best methodology for you’ll rely upon the kind of quilt and the specified look. Here’s a step-by-step information on how one can end a quilt binding:
1. Trim the surplus batting and backing material across the fringe of the quilt.
2. Fold the binding over the sting of the quilt, aligning the uncooked edges.
3. Sew the binding to the quilt utilizing a blind sew or different ornamental stitching.
4. Trim the surplus binding material on the corners.
5. Flip the binding over to the again of the quilt and fold it over the uncooked edges.
6. Sew the binding to the again of the quilt utilizing a blind sew or different ornamental stitching.
Upon getting completed stitching the binding, your quilt can be full! Get pleasure from your lovely new quilt.
Folks additionally ask about 121. How To End A Quilt Binding
What’s one of the simplest ways to complete a quilt binding?
One of the simplest ways to complete a quilt binding relies on the kind of quilt and the specified look. Some well-liked strategies embrace blind stitching, machine stitching, and hand stitching.
How do I make my quilt binding look skilled?
To make your quilt binding look skilled, use a blind sew or different ornamental stitching. You also needs to take the time to trim the surplus material rigorously and miter the corners. Lastly, press the binding effectively to provide it a cultured look.
What are some ideas for ending a quilt binding?
Listed here are a couple of ideas for ending a quilt binding:
- Use a pointy needle and thread that matches the colour of your binding material.
- Take your time and sew slowly and thoroughly.
- Trim the surplus material rigorously and miter the corners.
- Press the binding effectively to provide it a cultured look.
